Friday, 1 November 2013

FYP 2 Week 7 – Survey & Purchase Component and Materials

After finalizing the simulation results and producing the PCB designs, the components and material needed was listed to make it easier to be searched.

The components need is not other than the basic component that usually used during the electronic lab session back in time. Those component and materials are as listed below:

Component                                                                 Material
Resistors                                                                      Jumper wires
Capacitors                                                                   Multi-core wires
Led                                                                              Solder lead
Relay                                                                           Solder paste
                                                                                    PCB board
                                                                                    Etching acid
                                                                                    Thinner
                                                                                    Sand Paper

            These components and materials was purchased at place known as “Jalan Pasar” here in Kuala Lumpur.

            For component such as the super capacitors used in this project, it was ordered online through a friend of mine who is quite an expert on this super capacitors thing. It took around a week for me to able to get my hand on the super capacitors I had ordered as I was informed by my fiend that super capacitors was actually being imported from overseas.

Friday, 25 October 2013

FYP 2 Week 6 – Designing PCB Layout

Schematic Design

PCB layout design is started with the schematic design which is all about constructing the circuit design just as the one done in simulation software.


Figure showing schematic designed using Altium software to generate PCB layout.



Generate PCB Layout

The PCB layouts are generated in PDF format with exact real world sizing.

Figure showing complete PCB design generated in PDF format.



Figure showing PCB design generated in PDF format that will be used.


Friday, 11 October 2013

FYP 2 Week 5 – PCB Design Learning class

            With having successfully simulated each of the required circuit and satisfactory output results, now the first step to PCB layout design can be started.


            Something coincidence happened on this week was a class on learning PCB Layout Design was conducted by an expertise on the design method in my university that took place for the whole day from morning till evening. The software used for the designing purpose was called Altium designer.




                 Using Altium Designer software, the PCB development can be done. Altium Designer is the electronic design software that has ability to design PCB and build the next generation of electronic products besides designing 3D PCB layout environment and many more. Altium Designer is a powerful yet easy to use system development platform for FPGA, PCB and embedded software development built on “uniqum layeed” platform architecture. But for this project, this software only used to design the PCB layout.

                 However, we only learned to design PCB layout using this software during the class. Since start of the class, I jot down notes on every single details related to this software installation till the method of using or enhancing this software tools in developing the PCB layout required which all seem to be very useful.






Friday, 4 October 2013

FYP 2 Week 4 – Combining All Circuits In One Simulation

The simulation of overall and complete circuit of this project is as shown in figure below. This overall circuit is a combination of four circuits which are AC – DC converter, charging circuit, voltage comparator, and voltage balancer.

  • Figure showing simulation of complete project circuit.

Each of the circuits in this simulation function according to the specific function as explained in previous weeks for each particular circuits.

Friday, 27 September 2013

FYP 2 Week 3 – Research & Simulation of Voltage Balancer Circuit

In serial connection, the strings of capacitors require voltage balancing to prevent any cell from going into over-voltage. A proper cell balancing scheme as shown in figure below, needs to be placed within series connected super capacitor to ensure no super capacitor sees higher than rated voltage. In this project, two super capacitor that rated at 2.7V each are used as the charge storage and are connected in series to become super capacitor bank that of rating 5.4V. Three diode, with each rated at 0.7V are placed in parallel to each super capacitor because the total of the three diode yield a total voltage of 2.1V which almost near to the value of the single super capacitor used. While series of four diodes cannot be placed in parallel to each particular super capacitor is because the total of the four diodes yield a total voltage of 2.8V which is more than the rating value of the single super capacitor used.


Figure of voltage balancing circuit.



Simulation of voltage balancer circuit.



Voltage balancer circuit are used as a safety circuit in this project to protect the super capacitor from being charged over its rated voltage. The voltage balancer used here is series of three diodes in parallel to each super capacitor used as shown in figure above.

As discussed above, two super capacitor that rated at 2.7V each are used as the charge storage and are connected in series to become super capacitor bank that of rating 5.4V in this project. Each of the diode use is rated at 0.7V and series of the three diodes yield a total voltage of 2.1V. When charging the super capacitor, each series of diodes will make sure each super capacitor does not be charged more than 2.1V although it can be charged up to 2.7V.

Series of four diodes cannot be placed in parallel to each particular super capacitor is because it will yield a total voltage of 2.8V which is more than the rating value of the single super capacitor used. If series of four diodes are placed in parallel to each super capacitor, then the super capacitor will get damaged.

The function of diode D10 and D11 as shown below is to allow current flow from battery into super capacitor and not to flow back. Thus, when this super capacitor bank is used to charge a load, the current will flow into the load (D13) only.










Friday, 20 September 2013

FYP 2 Week 2 – Research & Simulation of Charging Circuit

The function of charging circuit is to control the amount of current used to charge the super capacitors in super capacitor bank. Over amount of current entering super capacitors will damage it. To avoid any damage, the amount of current entering the super capacitors needs to be reduced when it is reaching its full capacity with the slow, medium and fast charging option provided on the charging circuit.

Simulation of charging circuit.




  • For charging circuit, the simulation is as shown in figure above. At the input, input voltage of 12V DC will be step down to 5V using voltage regulator circuits with LM7805 voltage regulator IC as shown in figure below. Output 5V produced will pass through a relay whose function is to connect or disconnect the supply to the charging speed controller which comprises three resistors each in series with a switch and the entire three resistors in parallel to load. The values of all three resistors are much lower (100Ω, 220Ω, and 330Ω) compared to the load. When all three resistors is turned on by closing the switch, slow charging takes place as resistance of resistor in parallel will drop to a value lower than each of the resistor, thus allow more current flow through it rather than flowing into load with higher resistance which satisfies the equation V=IR. Fast charging occurs when all the three resistors are disconnected and medium charging takes place when only one or two resistors are switched on


Figure of LM7805 voltage regulator IC.



Friday, 13 September 2013

FYP 2 Week 1 – Research & Simulation of Voltage Comparator & AC-DC converter

Voltage Comparator circuits:

In this project, the super capacitor bank will be fully charged to 5.4V. To check whether the super capacitor bank are fully charged or not, a voltage comparator circuit are used.

Proteus (ISIS) simulation software was used to do simulation.

Voltage Comparator IC LM293 (not functioning) in simulation shows error stating that no specified model for that particular IC in simulation software.




Since the voltage comparator IC LM293 does not functioning in simulation, it was then replaced with voltage comparator IC CA3140. Following that, the circuits function as required.

Voltage Comparator IC CA3140 (functioning) in simulation will detect input voltage of less than 5.09V:

  • Figure showing input voltage detected less than 5.09V and light up Red LED.


Voltage Comparator IC CA3140 (functioning) in simulation will detect input voltage of more than 5.09V:

  • Figure showing input voltage detected more than 5.09V and light up Green LED.







AC-DC converter:

The power generate from the dynamo will enter the AC-DC converter that will convert AC power from dynamo into DC power. The AC-DC converter consists of bridge rectifier, capacitor filters, and voltage regulator IC.


  • Simulation of AC – DC converter circuit.


Simulation for AC-DC converter circuit was done by connecting its output to an oscilloscope and the output result was verified by analysing the voltage waveform result displayed on the oscilloscope as shown in figure below. The waveform voltage output on channel A is directly taken from the AC supply. While voltage output on channel D is the final DC voltage output from the converter circuits. The reading of the DC voltage output on channel D was read at the smallest scale of the oscilloscope which is 5mV/Division compare to the reading on channel A which read at 5V/Division. This shows that the DC voltage output produced is very stable as the result of using 0.1F capacitor as the filter. When tested with capacitor filter of lower value (10uF-47uF) that commonly used, the DC output was not as stable as of using the 0.1F values. Thus, this proves the circuits met its functionality.


Figure of simulation result of AC – DC converter circuit.